Small Builds - Revision history

Adamcolton: /* Saw Track */

2020-08-26T13:04:40Z

Saw Track

← Older revision		Revision as of 13:04, 26 August 2020
Line 114:		Line 114:
	A for the circular saw. Simplest version just uses thin plywood as the track and a milled 2x4 for the guide. Some sandpaper on the bottom will hold it in place.		A for the circular saw. Simplest version just uses thin plywood as the track and a milled 2x4 for the guide. Some sandpaper on the bottom will hold it in place.

	~~Build in 2' and 3' sections.~~ I like the design that uses dowels between the tracks and clasp to hold the sections together.		I like the design that uses dowels between the tracks and clasp to hold the sections together. I can make 2x8ft sections then cut them down so I end up with 2x5ft and 2x3ft. A 10ft section would be good for cutting 8ft sheets because it gives me a foot of overhang on either side.

	I like the layout of using thin mdf as the track supported on the non cutting side by a thicker piece of wood. I also like the technique of adding a dovetail key so that the saw locks into the track.		I like the layout of using thin mdf as the track supported on the non cutting side by a thicker piece of wood. I also like the technique of adding a dovetail key so that the saw locks into the track.
Line 121:		Line 121:

	This should be sized to fit both circular saws.		This should be sized to fit both circular saws.

			* https://www.youtube.com/watch?v=SvNFvM00OP4

	=== Multipurpose Bell Box ===		=== Multipurpose Bell Box ===

2020-05-01T17:04:07Z

← Older revision		Revision as of 17:04, 1 May 2020
Line 169:		Line 169:

	I resist using the rotary tool because it's a pain to get out and put away. Storage should make it easy to get the tool out and put it away. Should hold lots of bits.		I resist using the rotary tool because it's a pain to get out and put away. Storage should make it easy to get the tool out and put it away. Should hold lots of bits.

	~~==== Bottle Jack Cart ====~~
	~~I need to figure out the geometry for this, but I think I could make a good lift/adjustable height cart for the shop using a bottle jack.~~

	== Technical ==		== Technical ==

2020-05-01T17:02:15Z

Technical

← Older revision		Revision as of 17:02, 1 May 2020
Line 177:		Line 177:
	* Dovetail		* Dovetail
	* Dowel box		* Dowel box
	* Half blind lock joint		* [https://www.youtube.com/watch?v=igtlUli3tPA Half blind lock joint]

	[[Category:Woodworking]]		[[Category:Woodworking]]

2020-05-01T17:01:53Z

Technical

← Older revision		Revision as of 17:01, 1 May 2020
Line 177:		Line 177:
	* Dovetail		* Dovetail
	* Dowel box		* Dowel box
	* ~~Drawer rabbit (not sure the right name)~~		* Half blind lock joint

	[[Category:Woodworking]]		[[Category:Woodworking]]

2020-05-01T17:00:10Z

← Older revision		Revision as of 17:00, 1 May 2020
Line 172:		Line 172:
	==== Bottle Jack Cart ====		==== Bottle Jack Cart ====
	I need to figure out the geometry for this, but I think I could make a good lift/adjustable height cart for the shop using a bottle jack.		I need to figure out the geometry for this, but I think I could make a good lift/adjustable height cart for the shop using a bottle jack.

			== Technical ==
			* Spline box
			* Dovetail
			* Dowel box
			* Drawer rabbit (not sure the right name)

	[[Category:Woodworking]]		[[Category:Woodworking]]

2020-04-19T23:49:19Z

For Shop

← Older revision		Revision as of 23:49, 19 April 2020
Line 68:		Line 68:

	== For Shop ==		== For Shop ==

			=== Plywood Carrier ===
			A handle to make carrying plywood sheets easier.

	=== New Tool Inset ===		=== New Tool Inset ===

2020-04-16T13:33:18Z

For Shop

← Older revision		Revision as of 13:33, 16 April 2020
Line 68:		Line 68:

	== For Shop ==		== For Shop ==

			=== New Tool Inset ===
			The insulation insets for my toolbox aren't working very well. I want to make a new set from plywood. Use velcro and magnets to hold things in place. Top layer should be thin, inside can be drilled out to reduce weight.

	=== Solar Heater ===		=== Solar Heater ===

2020-04-12T17:40:15Z

Knex Box

← Older revision		Revision as of 17:40, 12 April 2020
Line 13:		Line 13:

	=== Knex Box ===		=== Knex Box ===
	Spaces for all the main rods and connectors.		Spaces for all the main rods and connectors. Tool chest style so that everything can be laid out.

	== For Fletcher ==		== For Fletcher ==

2020-04-12T17:38:31Z

For Me

← Older revision		Revision as of 17:38, 12 April 2020
Line 11:		Line 11:
	=== Pencil Box ===		=== Pencil Box ===
	Holds pencil and eraser. Bottom has small ledge sticking out with a ruler printed on it. I'd really like a way to incorporate a protractor.		Holds pencil and eraser. Bottom has small ledge sticking out with a ruler printed on it. I'd really like a way to incorporate a protractor.

			=== Knex Box ===
			Spaces for all the main rods and connectors.

	== For Fletcher ==		== For Fletcher ==

2020-04-11T22:38:44Z

← Older revision		Revision as of 22:38, 11 April 2020
Line 128:		Line 128:
	* Duck tape		* Duck tape

	=== Rotary Magnet ==		=== Rotary Magnet ===
	https://www.youtube.com/watch?v=MptNafdF_q8&t=428s		https://www.youtube.com/watch?v=MptNafdF_q8&t=428s