Whiteboard Plotter - Revision history

Adamcolton at 20:58, 31 March 2020

2020-03-31T20:58:00Z

← Older revision		Revision as of 20:58, 31 March 2020
Line 16:		Line 16:

	[[Category:Electronics]]		[[Category:Electronics]]
			[[Category:Robotics]]

Adamcolton: /* All In One */

2019-04-09T19:48:54Z

All In One

← Older revision		Revision as of 19:48, 9 April 2019
Line 11:		Line 11:
	* IR (for controls)		* IR (for controls)
	* SD card reader (to store the plot)		* SD card reader (to store the plot)

			Power off 9V, wired for battery, but I'll probably just use a wall wart.


	[[Category:Electronics]]		[[Category:Electronics]]

Adamcolton: /* All In One */

2019-04-09T19:45:54Z

All In One

← Older revision		Revision as of 19:45, 9 April 2019
Line 6:		Line 6:

	== All In One ==		== All In One ==
	~~The ends of the belt clip to~~ the ~~whiteboard.~~		https://www.hackster.io/fredrikstridsman/stringent-the-15-wall-plotter-d965ca

	* 2x 28BYJ-48 Stepper		* 2x 28BYJ-48 Stepper

Adamcolton: /* All In One */

2019-04-09T19:45:45Z

All In One

← Older revision		Revision as of 19:45, 9 April 2019
Line 8:		Line 8:
	The ends of the belt clip to the whiteboard.		The ends of the belt clip to the whiteboard.

	~~The control has 2 steppers and a servo~~ (for ~~the pen~~)~~. An LCD and buttons. And an~~ SD card~~. That's a lot of pins.~~		* 2x 28BYJ-48 Stepper
			* IR (for controls)
	~~I could use a Mega to get everything. I could also use two arduinos together, one~~ to ~~drive~~ the ~~motors and one handle IO.~~		* SD card reader (to store the plot)



	[[Category:Electronics]]		[[Category:Electronics]]

Adamcolton at 19:35, 9 April 2019

2019-04-09T19:35:27Z

← Older revision		Revision as of 19:35, 9 April 2019
Line 4:		Line 4:

	It might be slightly overkill, but doing this with an RasPi Zero could work well. It would be a lot easier to load data onto it.		It might be slightly overkill, but doing this with an RasPi Zero could work well. It would be a lot easier to load data onto it.

			== All In One ==
			The ends of the belt clip to the whiteboard.

			The control has 2 steppers and a servo (for the pen). An LCD and buttons. And an SD card. That's a lot of pins.

			I could use a Mega to get everything. I could also use two arduinos together, one to drive the motors and one handle IO.



	[[Category:Electronics]]		[[Category:Electronics]]

Adamcolton at 21:10, 29 January 2019

2019-01-29T21:10:58Z

← Older revision		Revision as of 21:10, 29 January 2019
Line 1:		Line 1:
	I like the model where everything is contained in one unit.		I like the model where everything is contained in one unit. But it can be a bit more difficult to build. I could also do a balanced model where the motors attach to the whiteboard and the control and power provide counter balance to the marker.

	This is a bigger project that will give me exposure to several more advanced tools.		This is a bigger project that will give me exposure to several more advanced tools.

			It might be slightly overkill, but doing this with an RasPi Zero could work well. It would be a lot easier to load data onto it.

	[[Category:Electronics]]		[[Category:Electronics]]

Adamcolton: Created page with "I like the model where everything is contained in one unit. This is a bigger project that will give me exposure to several more advanced tools. Category:Electronics"

2018-10-23T19:54:06Z

Created page with "I like the model where everything is contained in one unit. This is a bigger project that will give me exposure to several more advanced tools. Category:Electronics"

New page

I like the model where everything is contained in one unit.

This is a bigger project that will give me exposure to several more advanced tools.

[[Category:Electronics]]