Vulcan Woodshop: Difference between revisions
Adamcolton (talk | contribs) No edit summary |
Adamcolton (talk | contribs) No edit summary |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
A possible pre-cursor to my [Vulcan Open Lab] idea. | A possible pre-cursor to my [[Vulcan Open Lab]] idea. | ||
Now that I've got just a little experience, I'm finding that a collection of tools is nice, but you can really get a lot done with a table saw and drill press. My table saw is rated at 15amps, which is just over 2HP. I can get a router at that power. I think a router would serve well as a general purpose power house. | Now that I've got just a little experience, I'm finding that a collection of tools is nice, but you can really get a lot done with a table saw and drill press. My table saw is rated at 15amps, which is just over 2HP. I can get a router at that power. I think a router would serve well as a general purpose power house. | ||
| Line 27: | Line 27: | ||
Need to choose a spindle assembly and a chuck to match. | Need to choose a spindle assembly and a chuck to match. | ||
== 101 Version == | |||
* Table saw $400 | |||
* Drill Press $80 | |||
** standard $10 | |||
** spade $10 | |||
* Orbital Sander $30 | |||
** sanding Discs $15 | |||
* Sand paper 3x$13 = $40 | |||
* Chisels $10 | |||
* Calipers $20 | |||
* Scroll Saw $80 | |||
* 1 gallon glue $20 | |||
* Blue Tape | |||
Total: $715 | |||
Projects | |||
* Upside down rabbet box | |||
* End Table | |||
* Aderondack chair | |||
* Secret compartment box | |||
* Small box of drawers | |||
* Trestle table | |||
* Bed | |||
Tool Projects | |||
* Table saw sled | |||
* Box joint jig | |||
* Work bench | |||
* Saw horse | |||
* Tool chest | |||
[[Category:Vulcan|Woodshop]] | |||
Latest revision as of 15:35, 8 June 2020
A possible pre-cursor to my Vulcan Open Lab idea.
Now that I've got just a little experience, I'm finding that a collection of tools is nice, but you can really get a lot done with a table saw and drill press. My table saw is rated at 15amps, which is just over 2HP. I can get a router at that power. I think a router would serve well as a general purpose power house.
Base Tools
- Router
- Straight bit
- Edge (bearing) bit
- Chamfer bit
- Plunge bit
- Bit driver and set
- Digital Calipers
- Dial gauge (?)
- Dremel kit
Can we make our own chisels?
Drill Press
Purchase
- drill bits
- drill chuck and spindle assembly
- thrust bearing
- switch
- balance spring (coil?)
The base will be particle board filled with concrete. The column will be a pvc pipe filled with concrete (possibly with rope compression). The table will be particle board. I think it's best to just top it with thick epoxy, but aluminum may also make sense.
Need to choose a spindle assembly and a chuck to match.
101 Version
- Table saw $400
- Drill Press $80
- standard $10
- spade $10
- Orbital Sander $30
- sanding Discs $15
- Sand paper 3x$13 = $40
- Chisels $10
- Calipers $20
- Scroll Saw $80
- 1 gallon glue $20
- Blue Tape
Total: $715
Projects
- Upside down rabbet box
- End Table
- Aderondack chair
- Secret compartment box
- Small box of drawers
- Trestle table
- Bed
Tool Projects
- Table saw sled
- Box joint jig
- Work bench
- Saw horse
- Tool chest