Stirling Engine
Version 0.1
Design
Two beta style engines coupled together.
Piston
I want to use a piston instead of a diaphragm because it has a larger displacement, more displacement equals more power. I want to build my diaphragm using a steel wool core and some small pieces of metal (coat-hanger?) to reinforce it, pour concrete over that and seal the whole thing with silicon. This should allow me to make any shape I want while still getting a good smooth seal.
Notes
I saw a video using metal water bottles for the chamber - metal and already very smooth.
Combustion Heat Transfer
I would like to build a wood burning model and attempt to produce a very efficient heat transfer.
The cold portion will be water cooled. The pump is operated by the engine. The water reservoir will have a heat sink. A fan will pump air over the heat sink. That air (now slightly warmed) passes through a heat exchange with the exhaust. It is then forced in to the combustion chamber (wood burning). The exhaust from the combustion chamber is then forced back through the heat exchange, where most of the energy is reclaimed.
I'd also be interested in finding a way to reduce the emissions by filtering the particulate out of the exhaust. A filter would be an easy way to do this, but I'd also be interested if it could be done with centrifugal separation or ionization.
An Alpha configuration may work better. The entire hot section could be in the chimney of a rocket stove, for very high heat transfer. The cool section could be water cooled, far enough away from the heat. On second thought, making the piston would be hard and the shaft would still be right in the heat. Better would be a heat exchange. And the Stirling engine could power the fan. Rocket stove could be smallish, probably use a metal trash can insulated with perlite. Use metal ducts for the inside. The Stirling engine chambers would be pretty easy, probably metal pipes. The piston end shouldn't get too hot, so a concrete piston should work just fine.
Design 2015-10-05
The power source is a wood burning rocket stove. The outside will be a metal trash can. The burn chamber will be made from metal ducts and the whole thing will be insulated with perlite.
In the chimney will be a heat exchange. It looks like the best design is a coil of copper tubing. Rather than some complex multi-coil, I'll but another perlite insulator in the center. The intake will be hooked up to centrifugal blower, run by the engine.
The engine itself will be a beta design with 3 cylinders. The pistons cylinder will just be pipe, probably PVC because that part shouldn't get too hot. The piston itself will be concrete sealed with silicone. I'm not yet sure what the main cylinders will be made of. They need to stand up to a lot of heat and a medium amount of pressure. I'd like to find a 4" metal pipe, but that seems to get pretty pricey. I'll keep looking. The displacer will be filled with aluminum shavings, which I can get very cheap. These will act as a heat reclaimer. The cylinders will sit in a structure to manage the heat. It has 3 layers, the middle only exists for insulation (again, perlite). The bottom chamber takes hot air from the heat exchanger. The top has cold water running through it. The hot air and cold water should run in opposite to directions to help keep the temperature difference in the cylinders even. The water will be circulated with a basic pump, run from the engine.
I want to make the bearings myself for the crankshaft, it looks pretty easy (pvc pipe + BBs). The bearings will be held in place by 3 screws allowing for fine alignment. The crankshaft will be a little tough, but I don't think there's actually anything tricky about it. Lastly, I'll make a flywheel out of concrete.
The outlet of the hot cavity will still be quite warm, it should be fed back into the rocket stove for efficient combustion.
I'd really like to shoot for something in the 5hp range, then it can be used in some other projects I'm interested in.
Use Aluminum Cups for the cylinders. They're a bit tapered, but I can shape the displacer to match.
Cost
- Trashcan $16
- Ducts $7.60
- Aluminum Cups $22
- Perlite (ebay) $20
- Copper tubing $15
- Concrete $1
- Aluminum shaving $12
There's a lot of additional, small assorted hardware, but I don't expect that to be more than $30. Total: $100
Questions
- What is the proper volume ratio between the cylinder and the piston for a given temperature difference? this may help
- What is the expected power output based on piston volume and temperature difference?
Calc
Cups have a volume of 2cups, so 4 cups total per cylinder. I expect the hot side to be around 700F (just a guess) and the cold side to be around 80F.
One calculator suggested 60w/cylinder, but I don't know if I used it right.
I should be able to measure the power if I know the flywheel weight. By measuring the angular acceleration (and max rpm) I should get the power.